Products

Replacement Blade for LOAC Tubing Tool.

RO Cartridge Filter Spacer. Used to hook two cartridge filters end to end to double the length. Common for the 40" long filter housings.

Roll of 3/4"x100' Black Mainline (never used)

A Filtering unit that uses vacuum to help draw the syrup through a filter. You need a shop-vac or a vacuum pump to create the vacuum, and that help...

Round 9" Vacuum Syrup Filter Press. Good for producers making small amounts of syrup each day. There is not much surface area on one of these filte...

Rubber Gasket/Seal for Blue Plastic 5 Gal Container

Rubber Gloves for Hot Syrup or Water, 12" from finger tip to end of the cuff. These gloves work great for cleaning a filter press or for cleaning e...

A rubber plunger for the inside of the Solenoid valves. This little rubber piece is what forms the seal inside the solenoid valve.

Each mold has 10 cavities of Santa Claus. This is the whole Santa not just a head. Each Santa measures 1 7/8" wide and is 3" tall. Each cavity hold...

Sap Bucket Magnet with Maple Leaf. Roughly 3.5" tall and 2" wide. 

A replacement 1/2" diameter glass tube that is 12" long for a standard sight gauge.

0°-18° Brix Sap Refractometer.

Sap Sak. Holds 2.5+/- Gallons.

Sap Sak Holder

This brush has a long handle and is perfect for cleaning down in between the flues on a flue pan. Whether it is a raised flue or a drop flue, this ...

A triangled shaped brush designed to get down in between the flues on the back pan. Works with raised or drop flues. 10" from the handle to the bot...

SB 1 1/2" Aluminum Yoke for Hot Sap Regulator

Screw for CDL Multi Fittings

2" in diameter; 8" tall for use with the Short Syrup Hydrometer

Brix scale. 1°-12°Brix calibrated at 38°F State of Vermont inspected Hydrometers are fragile, glass instruments. They must be handled very cautious...

Baume & Brix scale 25°-40° Baume, 45°-75° Brix. Red lines at hot and cold test. 9 3/8" long - can be used with any of our hydrometer cups, but ...

Sight Level for Mainline

A long handled nylon brush designed to clean the glass sight tubes on evaporators. From the tip of the brush to the end of the handle it measures 24".

Single Glass Bottle Labeler (table top model). Sold as Is.

Fits 3/4", 1", and 1 1/4" mainline pipe; requires 31/64" hole

Single Manifold Saddle w/Elbow - While Supply Lasts

This regulator packing is a soft material almost like a foam. It is 3/16" thick and 2" in diameter. It is used on many of the old Small Brothers ev...

This regulator packing is a soft material almost like a foam. It is 3/16" thick and 1 3/4" in diameter. It is used on many of the old Small Brother...

This is the cold sap regulator for many of the old Small Brothers evaporators where the feed was coming in from the bottom. The bottom of this item...

Small Brothers Flue Pan Regulator Arm

A stainless welded float that is 6 1/8" wide and 12" long. This float is for the flue pan on a Small Brothers evaporator. It has a hole on each sid...

A stainless welded float that is 5" wide and 8.5" long. This float is for the syrup pan on a Small Brothers evaporator. It has a hole on each side ...

Protect your bucket with this small flat galvanized bucket cover. Eliminate the contamination and the dirt accumulation in your bucket. Size measur...

Small Gold Elastic Tie 50/pkg

Small Maple Leaf with Hook (metal). 3" wide x 4 1/2" long

A small bunny shaped candy mold. Each of the 20 cavities has a little bunny that looks like it is ready to hop away. The cavities measure 1" long a...

Small Sap Regulator Bridge.

The difference between a large scoop and a small scoop is just the width of the scoop. A large scoop is about 5.5" wide, but this small scoop is on...

Small Stainless Skimmer

Small Wire Puller

Smart Trek Vacuum Sensor - Single Port. H2O-Smartrek Monitoring SystemThe H2O-Smartrek system is a highly efficient solution providing accurate int...

Smart Trek Vacuum Sensor - Three Ports

Smartrek-H2O Ultrasonic Tank Level Sensor

Smiley Face Plastic Sucker Mold

Smoke Stack Thermometer

Snap Clip for Vacuum Releasers.

No two snowflakes are alike, unless you get this candy mold. It has 20 cavities and while many of the snowflakes are different there are a few repe...

A rubber candy mold of snowmen. Each mold has 16 cavities and each cavity is of a snowman with a pipe and holding a broom. They measure 1 1/8" wide...