Evaporators & Accessories

A replacement brass valve for a sight gauge. This is just the valve that comes with the rubber gasket inside. The valve has 1/2" male threads on it...

Sap Level Gauge Gasket.

Brass Washer for Sap Level Valve.

Most producers that have tried an automatic drawoff could not imagine boiling without one again. This is a full feature Max Marcland automatic draw...

H2O 2" Modulating Automatic Draw-off with Barometric Compensation, Motorized Valve, Controller and Probe. Comes with the down spout. Has a 2" tri-c...

This is a spare/replacement temperature probe for an automatic drawoff. A spare probe can make changing drawoff sides much easier. Just change the ...

V11 - 1" Motorized Stainless Ball Valve only. This is a spare valve for use with a Marcland Max or Mini Automatic drawoff.

A rubber plunger for the inside of the Solenoid valves. This little rubber piece is what forms the seal inside the solenoid valve.

This bracket is made to hang on the side of a Leader welded flue pan and then you can mount your Marcland control box right on it. The bracket fits...

Thermometer Bracket for Welded Pan (for digital or dial therm.)

Temp. Probe Clip for Marcland Auto Drawoff temperature probe. This clip gets attached to the pan with a bolt (not included) and then the temperatur...

A digital meter that tells you the barometric pressure in inches of mercury and the boiling point of water in degrees of Fahrenheit based on the ba...

Bolt-On Regulating System with Float.For use with all welded Half Pint and Supreme BoilingPans.

A replacement float for a Grimm or Leader hot sap float. This float measures 8.5" x 4.5". They now are making them with a crank on the top which al...

This stainless welded float is used for the flue pan for many of new Leader evaporators. It measures 5 1/2" wide and is 10 3/4" long. It has a cran...

A stainless welded float that is 5" wide and 8.5" long. This float is for the syrup pan on a Small Brothers evaporator. It has a hole on each side ...

A stainless welded float that is 6 1/8" wide and 12" long. This float is for the flue pan on a Small Brothers evaporator. It has a hole on each sid...

A rubber washer that is used in the pan connections between the flue pan and the syrup pan on a Grimm raised flue evaporator or a Leader Patriot.

A stainless washer that is used on the pan connections between the flue pan and the syrup pan on a Grimm raised flue evaporator or a Leader Patriot...

A 2 3/8" rubber washer for a Grimm evaporator.

A 2 3/8" Metal washer for a Grimm evaporator.

This is the rubber regulator packing used in a Z arm for a Grimm evaporator or the older Leader Patriot evaporators. This packing was used for the ...

This thin rubber packing is used for the cold sap regulator on many of the Leader and Grimm evaporators. Leader has also started using it on the re...

This regulator packing is a soft material almost like a foam. It is 3/16" thick and 1 3/4" in diameter. It is used on many of the old Small Brother...

A thick white regulator packing that is a spongy rubber material. It is about a 1/4" thick and is 3 3/8" in diameter. Can be used in the hot or col...

This hose is used for hooking a line up to the cold sap float box. Used on the Leader WSE evaporators and also some of the older styles. Stainless ...

A replacement hose that measures 2"x2". These rubber hoses are used to hook a float box on to the evaporator, and can handle the heat of hot sap go...

A rubber hose connection that is used on the Leader American pans, as well as some of the older evaporators. These hoses measure 2" in diameter and...

The elbow for Grimm Raised flue pans or Leader Patriot pans that goes on the 1" threaded nipple that sticks into the syrup pan. This is the elbow t...

A stainless nut used on the Grimm or Leader Patriot evaporators for hooking the flue pan up to the syrup pan. Some of the old nuts we galvanized or...

Small Sap Regulator Bridge.

This is the cold sap regulator for many of the old Small Brothers evaporators where the feed was coming in from the bottom. The bottom of this item...

The Z arm hot sap regulator. This is used on a Grimm evaporator or the Leader Patriots. If you need one of these it is best to call in the order. T...

Small Brothers Flue Pan Regulator Arm

A hot sap regulator for a Small Brothers evaporator. The yoke goes over the elbow and hangs on the 1" feed pipe to the front pan. There is a piece ...

SB 1 1/2" Aluminum Yoke for Hot Sap Regulator

A regulator arm for a Leader cold sap float box.

A 2" stainless plug used in the Leader Patriot and Leader American evaporators for reversing the flow of sap through the flue pan.

4 oz Soldering Flux

1/3 lb (no lead) Solder (stainless steel & tin solder).

The Grimm style grates have flat ends. The area the wood sits on is flat, but the bottom side has a little bow to it. This grate is 24" long and 2....

The Leader grate looks like a single V. It measures 25" long and is 2.5" wide. The ends are about 1.5" thick. This grate was used in the older evap...

The Leader grate looks like a double V. It measures 25" long and is 4.5" wide. The ends are about 1.5" thick.

The Leader grate looks like a double V. It measures 30" long and is 4.5" wide. The ends are about 1.5" thick.

A Leader forced draft grate that is 30" long and 8" wide.

The Grimm style grates have flat ends. The area the wood sits on is flat, but the bottom side has a little bow to it. This grate is 32" long and 3....

The Leader grate looks like a double V. It measures 36" long and is 4.5" wide. The ends are about 1.5" thick.

The Grimm style grates have flat ends. The area the wood sits on is flat, but the bottom side has a little bow to it. This grate is 36" long and 3....